PRODUCT OVERVIEW - REMOTE CONTROL
1. ON/OFF button
2. Mode button
3. +/- button
4. Swing button (not available)
5. Fan button
6. Sleep button
7. Timer button
8. Health button (not available)
9. WiFi button
PRODUCT OVERVIEW - REMOTE CONTROL DISPLAY
Note:
This is a general use remote controller, and some functions, as described are non-functioning.
USE
1 ON/OFF button
Press this button to turn on the unit. Press this button again to turn off the unit.
2 Mode button
Press this button and the mode will circulate according to below sequence:
Auto -> Cool -> Dry-> Fan-> Heat
• Auto: During auto the unit will automatically adjust the settings. The set temperature cannot be changed.
• Cool: Under this mode, air conditioner operates under cooling mode. Cooling indicator will be on. Press “Fan Speed” button to adjust the fan speed.
• Dry: Under this mode, the unit runs in low fan speed for dehumidification and the corresponding indicator is on. The fan speed cannot be adjusted.
• Fan: Under this mode, air conditioner will not cool or heat, only blow wind. Fan indicator will be on. Press “Fan Speed” button to adjust the fan speed.
• Heat: Not available
3 +/- button
• Pressing “+” or “-” button once will increase or decrease set temperature by 1°C (°F). Hold “+” or “-” button for 2s, set temperature on remote controller will change quickly.
• Release the button after your required set temperature is reached.
Under timer setting status, after each pressing of “+” or “-” button, time will increase or decrease 0.5h. Hold “+” or “-” button and the time on the display will change quickly.
4 Swing button
Not available for this unit.
5 Fan button
This button sets the fan speed. The sequence goes from auto, 1, 2, 3, and back to auto.
6 Sleep button
Press this button to turn the sleep mode on. This function maintains the most comfortable temperature for you.
7 Timer button
• Press this button once and the characters of HOUR ON (OFF) will flash.
• Meanwhile, press “+” button or “-” button to adjust timer setting (time will change quickly if holding “+” or “-” button). Time range is 0.5~24hours.
• Press this button again to confirm timer setting and the characters of HOUR ON (OFF) will stop flashing.
If the characters are flashing but you haven’t press timer button, timer setting status will be stopped after 5s. If timer is confirmed, press this button again to cancel timer.
8 Health button
Not available for this unit.
9 Wi-fi button
• Press “WiFi“ button to turn on WiFi function, “WiFi“ icon will be displayed on the remote controller: Hold “WiFi“ button for 5s to turn off WiFi function and “WiFi“ icon will disappear.
• Under off status, press “MODE” and “WiFi“ buttons simultaneously for 1s, WiFi module will restore factory settings.
Combination of buttons:
• Temperature display switchover function: Under OFF status, press “-” and “Mode” buttons simultaneously to switch temperature display between °C and °F.
• Light function: Under switch-on or switch-off state, you may hold “+”and “FAN” buttons simultaneously to set the lamp on or off and send the code. After being energized the lamp is defaulted on.
REPLACEMENT OF BATTERIES
1. Press the back side of remote controller on the spot marked with , and push the cover of the battery box along the arrow direction.
2. Replace two (AAA 1.5V) dry batteries, and make sure the positions of + and – are correct.
3. Reinstall the cover of the battery box.
Note:
• During operation, point the remote-control signal sender at the receiving window on unit.
• The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles between them.
• Signal may be interfered easily in the room where there is fluorescent lamp or wireless telephone; remote controller should be close to the unit during operation.
• Replace new batteries of the same model when replacement is required.
• When you don’t use remote controller for a long time, please take out the batteries.
• If the display on remote controller is fuzzy or there’s no display, please replace batteries.